A private well is only as protected as the top of its casing. Many homes in and around Washington, in Franklin County, MO, sit in river-bottom areas where surface water rises during wet seasons. The cap, vent, and seal at the top of the well are the points where surface water, insects, and debris can get in. This guide covers the checks a homeowner can make without digging, and the order to make them in.

Why the top of the well matters

Groundwater reaches the pump through a casing that should stand above the ground and end in a sealed cap. When the casing sits low, sits in a dip in the yard, or has a cap that no longer fits, rain runoff and surface water can run down the outside of the casing and into the well. Surface water can carry bacteria, sediment, and organic matter. Private wells are not inspected on a schedule, so the homeowner is the person who notices changes.

Start with a walk-around

Do this in daylight on a dry day if you can. Bring a flashlight and take notes or photos so you can compare them later.

  • Check the cap. It should fit snugly, with no gaps, cracks, or missing gasket. A loose or lifted cap is a common entry point.
  • Check the vent. The vent should be intact and point downward, with a screen or insect guard that is whole and clean. Look for nests, wasp activity, or mud dauber marks inside the vent tube.
  • Check the casing. Look for cracks, rust holes, or separation where the casing meets the pad or the pitless adapter, if the well has one.
  • Check the seal. Where the electrical conduit or drop pipe enters the cap, the seal should be tight. Gaps there let in air, moisture, and insects.
  • Check the wellhead pad. It should be level and slope away from the casing, so water runs off instead of pooling beside it.

Look at the ground around the well

Grading matters as much as the cap. Stand at the well and look at where water goes when it rains. If the soil slopes toward the casing, or water collects there after a storm, the well sits in a catch basin. Downspouts, gutters, and driveway runoff should be directed well away from the wellhead. Look for nearby sources as well, including a septic tank or drain field, a fuel tank, a livestock area, or a fertilizer or chemical storage spot. Those features do not prove a problem, but they tell you what the well is near and what to test for.

After a flood

Flooding is the event that most often exposes weaknesses at the top of a well. If water reached the wellhead or the ground around it, do not run the water for drinking or cooking until you have checked the well and tested it. Here is a practical order of steps:

  1. Check the cap, vent, and casing for damage or debris from the flood water.
  2. Look for mud, silt, or debris inside any accessible part of the well.
  3. Do not start disinfecting until the physical checks are done and any damage is repaired, since a damaged casing can let in new contamination after treatment.
  4. Collect a water sample for bacteria testing with a state-certified lab, following the lab's collection instructions exactly.
  5. Keep the lab report, and repeat testing if the lab advises it.

What to test for

A bacteria test, which looks for total coliform and E. coli, is the most direct check for surface water getting into a well. Many homeowners in the area also order nitrate testing, since nitrate can come from agricultural land and septic systems. Deeper bedrock wells in the area can also carry naturally elevated radium, so a broader panel may be useful if the well is older or deeper. Wells are unregulated, so the test results and the choices that follow from them are the homeowner's responsibility.

When to call a licensed well contractor

Call a licensed well contractor if the casing is cracked or separated, if the cap cannot be sealed, if the pad has settled, or if the well sits in a low spot that cannot be regraded. A contractor can evaluate the well as a whole, including the pump, pressure tank, and pitless adapter, and recommend what, if anything, needs to change. Keep your notes and photos from the walk-around, since they help a contractor understand the history of the well.

Keep a simple log

Write down the date of each walk-around, what you found, any repairs, and each test result. Over time the log shows whether the cap, vent, or grading is changing, and it gives you something concrete to show a contractor, a lab, or a home inspector. A short log kept once or twice a year is usually enough for a well in good condition.